日本語AIでPubMedを検索
4つの異なるインプラントシステムにおける補綴用スクリューの最大応力に対する機械的抵抗の比較-in vitro研究
Comparison in Four Different Implant Systems of Mechanical Resistance to Maximal Stress in Prosthetic Screws-An In Vitro Study.
PMID: 33050156 PMCID: PMC7712841. DOI: 10.3390/dj8040116.
抄録
インプラントとアバットメントの連結部の微小な動きは,インプラント周囲の骨の保存に影響を及ぼす.本研究では,オリジナルコンポーネントを用いて,インプラント補綴用ネジの締め付けを1サイクル行った後の最大トルクを評価・定量化した.合計40個のサンプルをテストしました。Megagen-Daegu(韓国)、Dentium-Gangnam-Gu(韓国・ソウル)、BIOMET 3i-West Palm Beach(米国・フロリダ州)、BTI-Álava(スペイン)。各メーカーのスクリューには、破断するまで最大の応力をかけた。破断点を記録し,全サンプル間で比較した。破断トルクの平均値を比較するために,各ブランドに関連する基準値とサンプルの結果を用いて-検定を行った。ブランド間の最大抵抗値の比較には,ANOVA(分散分析)を用い,Tukeyの多重比較検定を併用した。有意水準の最大値は5%とした。各ブランドの平均破断力は、Megagenが40.07Ncm、Dentiumが53.39Ncm、Biomet 3iが39.74Ncm、BTIが68.84Ncmであった。BTI社のスクリューが最も破断しにくかった。適用されたプロトコールによると、インプラントとアバットメントの接続は、良好な抵抗性とこれらのインターフェース間の正確な適合性を示した。そのため、いくつかのケースでは、提示された値は品質管理の欠如と低い破壊抵抗性を示した。
Micromovements of the implant-abutment connection influence peri-implant bone preservation. This study evaluates and quantifies the maximal torque after a cycle of implant prosthetic screws tightening using original components. A total of 40 samples were tested: Megagen-Daegu, South Korea; Dentium-Gangnam-Gu, Seoul, Korea; BIOMET 3i-West Palm Beach, FL, USA and BTI-Álava, Spain. Screws from each manufacturer were subjected to maximal stress force until they fractured. The fracture points were recorded and compared among all samples. To compare the mean values of fracture torques, the reference values associated with each brand and the sample results were used in -tests. ANOVA (analysis of variance) was used to compare the maximal resistance limit between brands, complemented with Tukey's multiple-comparison test. The maximal considered level of significance was 5%. The average fracture force for the brands was 40.07 Ncm for Megagen, 53.39 Ncm for Dentium, 39.74 Ncm for Biomet 3i, and 68.84 Ncm for BTI. BTI screws showed the most resistance to fracture. According to the protocol that was applied, the implant-abutment connection demonstrated good resistance and a precise fit between these interfaces; therefore, in some cases, the presented values showed a lack of quality control and low fracture resistance.