日本語AIでPubMedを検索
CAD/CAMコンポジットレジン製クラウンの破壊強度試験
Fracture strength testing of crowns made of CAD/CAM composite resins.
PMID: 29605190
抄録
目的:
本研究の目的は、コンピュータ支援設計/コンピュータ支援製造(CAD/CAM)コンポジットレジン冠が臼歯の咬合力に耐える十分な強度を有するかどうかを確認することである。帰無仮説は、CAD/CAMコンポジットレジン冠の破折強度は、臼歯の平均最大咬合力より低いというものである。
PURPOSE: The purpose of this study was to ascertain whether computer aided design/computer aided manufacturing (CAD/CAM) composite resin crowns have sufficient strength to withstand the bite force of the molar teeth. The null hypothesis was that the fracture strength of CAD/CAM composite resin crowns is lower than the average maximum bite force of the molar tooth.
方法:
コンポジットレジン製CAD/CAMブランク4種類(ブロックHC:HC,KZR-CAD HR:HR,KZR-CAD HR2:HR2,Avencia Block:AVE)とコントロールとして用いた二ケイ酸リチウムガラスセラミック製CAD/CAMブランク1種類(IPS e.max CAD:IPS)を用いて,右側上顎第一大臼歯の形状を有するクラウンを作製した.製作したクラウンをメタルアバットメントに接着した際の破折強度と、各材料の二軸曲げ強度を評価した。
METHODS: The crowns, which shape is the right maxillary first molar, were fabricated using four CAD/CAM blanks made of composite resins (Block HC: HC, KZR-CAD HR: HR, KZR-CAD HR2: HR2, Avencia Block: AVE) and one CAD/CAM blank made of lithium disilicate glass-ceramic (IPS e.max CAD: IPS), which was used as a control. Fracture strength of fabricated crowns bonded to metal abutment and biaxial flexural strength of the materials were evaluated.
結果:
破壊強度試験と二軸曲げ強さ試験の結果は異なる傾向を示した.HCを除くCAD/CAMコンポジットレジン冠の破折強さは3.3kN~3.9kNであり,IPS(3.3kN)と同程度であった.一方,CAD/CAMコンポジットレジンの二軸曲げ強さは175MPaから247MPaであり,IPS(360MPa)より有意に低かった.
RESULTS: The results of fracture strength test and biaxial flexural strength test showed different tendencies. The fracture strength of CAD/CAM composite resin crowns except HC ranged from 3.3kN to 3.9kN, and was similar to that of IPS (3.3kN). In contrast, biaxial flexural strength of CAD/CAM composite resins ranged from 175MPa to 247MPa, and was significantly lower than that of IPS (360MPa).
結論:
検討したすべてのCAD/CAMコンポジットレジン冠は,臼歯の平均最大咬合力(700~900N)の約3~4倍の破壊強度を示し,この結果から,CAD/CAMコンポジットレジン冠は臼歯の咬合力に耐える十分な強度を有すると結論した.
CONCLUSIONS: All CAD/CAM composite resin crowns studied presented about 3-4 times higher fracture strength than the average maximum bite force of the molar tooth (700-900N), which result leads to the conclusion that CAD/CAM composite resin crowns would have sufficient strength to withstand the bite force of the molar teeth.